Industrial Hygiene in Construction

From what I have seen, there are not a large amount of formaldehyde exposures in construction. However, there is A LOT of formaldehyde used in construction materials. Formaldehyde can be dangerous at levels undetectable by your nose. And, the symptoms of exposure are nondescript (irritant & tingling of eyes, nose, respiratory tract).

Here are some products that may contain trace (or more) amounts of formaldehyde:

• resins in plywood, MDF, CDX, particle board/fiber board
• garage doors
• drywall
• roofing
• glues / mastics
• paint/coatings
• carpets
• insulation (spray in and batting)

I believe the reason we do not see high exposures is due to the limited duration of exposure, and the open-aired nature during the construction. Some exceptions are warehouses with large storage areas of particle board/MDF. (I have found exposures in these areas)

The OSHA exposure limit for formaldehyde is 0.75 ppm (action limit of 0.5 ppm, and short term limit of 2 ppm). However, this may not be low enough, based upon other standards (ACGIH says 0.3 ppm, NIOSH 0.1 ppm)

Another major issue with this hazard in construction is once the space is occupied.

• Once construction is done, the space may be sealed up, heated, and additional curing can occur.
• This may release more formaldehyde, and also NOT allow as much to escape (by dilution ventilation).
• Compounding this issue are the type of occupants in the building. Are there children, non-working adults, immunocompromised individuals, sick, or elderly occupying this space? The OSHA standards are NOT protective for these types of people.

I do not forsee this type of sign being posted immediately after new construction.

On the plus side, someone has discovered that plants may help reduce formaldehyde & VOC levels in homes. Horticulture Science Kwang Jim Kim, et.al

Much research has been done in construction safety. If you are working in construction, you have probably heard the facts over and over. The majority of construction injuries are from four main hazards, hence the “focus four hazards“. Although this site is for health issues & industrial hygiene in construction, it would be ridiculous to NOT mention these other hazards.

• Falls,
• Caught-in or Caught-between,
• Struck-by &
• Electrocution.

When talking with superintendents and safety coordinators, you can usually tell very quickly  if they have these under control. Either their subcontractors already do it right, or if/when they see an error, they immediately stop and address the inefficiency.

I saw this ladder in front of my children’s school. There was no one around and, by the look of it, there might have been someone on the roof. I should have waited, or fixed the ladder and spoken to the individual. But, I didn’t. Instead, I took a picture, put it on the internet, and now I’m telling everyone why it’s wrong.

Reviewing a material safety data sheet (MSDS), or soon to be called a SDS (safety data sheet), can be a useful skill. Most times the product is straightforward and gives you what you need. However, there are somethings to watch for and areas to focus to make your reviewing skills better.

To start,  make sure you have the right SDS. Match the product with the form. If is is not exactly right, find the right one. It must list the model/product name & manufacturer.

Below are some suggestions:

• What is the date of the SDS?
  • is it the most recent?
  • when was it last updated?
• Look at section 2/3 (Hazardous components) VERY carefully.
  • google the CAS# and find the name (they sometimes hide the true-name)
  • look at the % of each component
  • what is the listed exposure limit? Is it correct? What about other recommended limits?
  • remember the hazard is only listed in this area if it is greater than 1% of the total
• Look through each section mindful of how you will be using the product.
  • for example: if you are going to be burning the product, usually the SDS will not address these types of concerns/exposures
  • what are the required PPE during “regular use”
  • what happens if you use this product in a confined area?
  • does the manufacturer recommend air monitoring? when?
• Familiarize yourself with the emergency procedures
  • what if it spills?
  • disposal?
  • what can cause exposure? inhalation? skin?
• Look at the other sections with a inquisitive eye
  • do they list other chemicals, which are NOT included in the product section? why?
  • do they mention Proposition 65?
• Finally,
  • post/make available a copy wherever it’s needed
  • make sure you know the product

It is a mixed-bag when it comes to the quality of SDS from a manufacturer. Some of them will work with you, others are a total-pain. Remember it is YOUR RIGHT to know about the products you use. If you don’t feel comfortable with the information they’ve given you, call them. OR, go find another product.

I’m easily impressed with welding and welders. Welding looks so simple, yet hard, dangerous and permanent.

When interviewing your welder, here are some questions to ask:

• What type of welding are you doing?
• What type of metal do you weld on? (mild steel, stainless, galvanized)
• Is there any coating on the metal?
• What type of flux is used?
• Where do you weld?, and then, “Where else?”
• Is there any ventilation in the area you weld?
• Are there any flammables in the area?
• Do you wear any PPE when welding? (ear plugs, respirator, leather)
• When do you use fall protection?
• Do you have & use welding shields?

What makes welding so difficult is the number of variables involved. The welding variables can change by the minute. Educate your employees on these dangers.

After the above questions, if the employee is agreeable, I ask some additional questions. These are the ones that provoke the best stories:

• What is the strangest things you’ve welded?
• Have you ever welding in a really small (confined) area?
• Have you ever welded with exotic metals? fluxes?
• What’s the worst thing you’ve welded on?
• Have you ever gotten sick from welding?

There are many, many more questions to be asked depending on the answers. The authority on this subject, Michael Harris, has written an excellent book on this subject, “Welding Health and Safety“(ISBN 978-1-931504-28-7). It is available from AIHA. It is VERY detailed, and money well spent if you do welding. I have taken his short course (all day) and I learned more than I ever thought possible, and I still can’t even weld!

Since you are reading this, you probably know the answer. Everyone. But, who is everyone? It should include your CEO/Company President/COO (or similar). If not, I guarantee you aren’t working as safely as possible.

The reason:  The person doing the work usually isn’t involved in the bidding & planning of the project.  It’s not always the President’s fault that the proper safety equipment wasn’t bought, or there are no available tie off points on the roof. (But, it might be their fault if they are willing to press forward without making changes.)

Here is one way to deal with these issues. Train the CEO (President/COO/Project Manager/Estimator) beforehand. Here’s how:

• Make the training for them. 
  • Don’t talk about safety harnesses, or the three different types of asbestos.
  • Go over big items (where are your claims? what are similar claims for your industry?)
• Emphasize the proper methods to control any hazard:
  • #1 engineering controls
  • #2 administrative controls
  • #3 PPE (in that order!)
• Get them to contact you during the bidding process (not after you’ve won it). Talk about what might be dangerous work & plan for it.
• Share a success story. Ask a superintendent to explain how they controlled a possible exposure.
  • Did they make the architect install in a tie-off point?
  • Did they ask the owner to change adhesive products to a less hazardous one?
  • Did they use an abatement contractor who performed the work well?
• Keep it simple & short. You don’t need a lot of time, but you do need them all on the same page.

When everyone in the company has the same interest in safety, it isn’t hard to explain.